Ensuring Safety When Using a Roofing Harness

Roofing Harness Safety


It is important to ensure your safety when carrying out any type of roof repair. It can be extremely difficult to maintain your balance as well perform a roof repair even if you are someone who is not scared of heights. This is the reason it is important to wear a roof harness at all times to prevent any serious injuries due to falling off the edge.

Here are a few steps that can guide you through installing a roof harness properly:

Step 1: Roof Brackets

The roof brackets should be placed 3 feet away from each other in a row and about 16 inches up. Nail the brackets with a hammer right over a truss. Slide the bracket underneath a shingle tab to install it.

Step 2: Slide Guard

On the eaves of the roof, place the roof brackets and plank. This will not only ensure you have a place to keep your tools but will also keep you from slipping off the edge of the roof.

Step 3: Safety Harness

Fasten the roof harness to your chest. Adjust the bands to ensure the harness is strapped on tightly. Check if all the buckles on the harness are shut.

In order to use the harness properly and safely, it is advisable to follow these tips:

Look over your harness: It is important to inspect the harness and ensure the ropes are not frayed or tattered. Avoid using gear if it has broken buckles or any weak spots. Before using the harness to support your weight, ensure that every part of the equipment is working properly.

Tighten the bands: Tighten the bands of the roof harness in order to make sure it fits snugly. A tight fit makes sure that the harness will remain at its place and, not slip and result in an injury in case you fall off the roof. However, adjust the harness to fit comfortably, it should not be too restrictive.

Setting up the roof anchor: Place the roof anchor directly above the place you will be repairing. In order to ensure that the roof anchor remains secured, stay within 4 feet of where it is placed. It can be moved according to the necessity or more roof anchors can be placed for additional stability.

Roof anchors should be placed at the peak and no less than 6 feet from the roof’s edge. Before you move your gear from one roof anchor to a different one make sure one anchor is still mounted in order to avoid losing balance or falling off during the transfer.

Keep repositioning the rope-grab: In order to stay secure and reduce slack, keep adjusting the rope-grab as you move along the roof. Roof repair is a difficult job and having a rope-grab available readily when the need can prove to be a good safety measure.

Tesla’s Solar Powered Roofs Come with a Low Price Tag

Tesla Inc. has begun taking $1,000 deposits for its amazing solar roofing system tiles– to be provided this year at a price point that could expand the United States solar market.

Tesla will start with production of 2 of the 4 styles it revealed in October: a smooth glass and a textured glass tile. 1Roofing a 2,000 square-foot home in New York state– with 40 percent protection of active solar tiles and battery backup for night-time usage– would cost about $50,000 after federal tax credits and generate $64,000 in energy over 30 years, according to.

That’s more pricey in advance than a typical roofing system, however cheaper than a normal roof with conventional solar and back-up batteries. The guarantee is for the lifetime of your home..

The vision Musk explains with the solar roof is the grand marriage of Tesla’s clean-energy ambitions, integrating solar energy, batteries, and electric cars. ” These are actually the three legs of the stool for a sustainable energy future,” Musk stated. Solar energy going to a fixed battery pack so you have power at night, and after that charging an electrical lorry, you can scale that to all the world’s demand.

The rooftop shingles are essentially identical from traditional high-end roofing products, with discreet solar cells embedded below a glass surface area. From the majority of viewing angles, they look just like common shingles, however they allow light to travel through from above onto a basic flat solar battery.

Tesla has stopped door-to-door sales of photovoltaic panels and begun screening solar sales in its car stores. Preliminary trials discovered the new technique was 50 to 100 percent more effective than at the best non-Tesla places selling SolarCity items. Over the next 6 months, more than 70 shops will be staffed for solar sales.

Production will begin at Tesla’s Fremont solar plant in California and after that move to its brand-new factory in Buffalo, New York, with additional investments from Tesla’s partner, Panasonic. Musk said preliminary sales will be restricted by manufacturing capability as the business increases its production volumes..

About That Pricing.

Tesla launched a tool on its website, where U.S. property owners can estimate the overall expense and life time savings of including the solar roofing and backup batteries. The overall expense of installation, ownership, and electrical power savings will be lower than equivalent solar setups. However, for numerous houses the preliminary expense of the roofing system remains substantial.

As of mid-2017, the typical cost for solar panels in Denver was $3.30 per watt. Hence, because the normal system size in the United States is 5 kilowatts (5,000 watts), the typical cost of a solar panel system in Denver is $16,500 before any refunds or rewards.

While this cost is competitive for the overall state of Colorado, it is likewise very competitive in terms of the national average. Roofing companies in Denver will have to account and factor these stats into their business. Rates for solar panel systems have dropped by over 64% in Colorado over the past 5 years and homeowners are taking notice. Check out this comparison table of Denver and U.S. typical rates for different system sizes:

3 kW $7,119 $6,930 
6 kW $14,238 $13,860 
10 kW $23,730  $23,100
12 kW $28,476 $27,720 

The tempered glass in Tesla’s tiles is created to comply with the hardest toughness requirements for both roofings and solar items throughout the United States, according to Tesla. The roofing system itself is guaranteed to outlast your home, while the power production of the solar batteries is covered under a 30 year service warranty..A Tesla solar roofing will likewise lose a few of the energy-generating density of a standard panel, due to the fact that the cells should be spaced further apart to represent the edges of the tiles. For that reason, the portion of the roof that will be covered by active solar cells will be greater, as will the overall cost of the roof. All told, a conventional solar setup might be 30 percent more affordable than a Tesla roofing system, he stated, however Tesla’s will look better and come with a lifetime warranty. “A 30 percent premium might well be acceptable.”.

Tesla will handle the entire process of solar roofing system setup, consisting of removal of existing roofs, style, permits, setup and upkeep. The company approximates that installation will take about a week.

Keeping Your Crews Sustainable Depends a Large Part on the Tools You Use

Sustainability is as much about individuals as the environment. And some of the most crucial individuals affected by sustainable roof are the workers on your teams. For a roofing task to be truly sustainable, the health, security and success of the workers who set up the roofing needs to be considered.

US Restoration & Remodeling just recently posted a great article on the tools they use to perform most of their roofing jobs.

This article is going to highlight the methods the tools you pick can add to the sustainability of your labor force. First, the right tools can assist prevent injuries on the job. Some tools can minimize the amount of private effort required to complete a task and reduce the risk of strain to muscles, tendons, and joints. Some tools permit private employees to handle heavy roofing materials that otherwise may lead to back injuries. Examples of tools that can carry the load for your employees consist of:

– Ladder raises to carry roof rolls, shingles, and ballast

– Roll providers to navigate and position roof rolls

– Carts for applying loads of ballast and cans of adhesive

Other tools can decrease the variety of specific movements needed to finish a task, resulting in a decrease in repetitive motion injuries. Most likely the most crucial tools to reduce repeated movements involve techniques to keep employees standing instead of bending down to carry out jobs. Such stand-up tools not just decrease the danger of back pressure but also other repetitive-motion tensions to wrists, elbows, and knees. Examples of stand-up tools that lower recurring strains on your employees consist of:

– Attachment tools to position and fasten insulation and seam plates

– Base sheet attachment tools

– Primer and adhesive applicators

– Membrane slitters and joint rollers

– Automatic welding tools

In addition to reducing the threat of occupational injuries, excellent tools also increase the productivity of your labor force. With the right tools, your workers can deal with heavier loads, cover more roof location, and lower costly application errors. As a result, roofing information are installed more regularly and pricey call-backs are lowered.

Finally, among the most important functions of modern roofing tools is that they are user-friendly. When your employees’ tools are their good friends, they have the tendency to enjoy their work. That can be a crucial advantage when hiring new employees. If potential recruits see your job sites as locations that secure them and help them succeed, they’re most likely to pick your company over your competitor as the location they wish to work.


Buying and Using Drones to Inspect Roof Systems

Drones are among the hottest subjects in the roofing industry today. The idea of using a state-of-the-art flying video camera to reduce your time invested in unsafe roofing systems is too tempting to ignore, specifically if you’re just a big kid at heart.

I always desired a push-button control helicopter maturing, however they were way too pricey and difficult to fly. Today’s drones have actually fixed those issues and made all our youth dreams a truth. The next step is to validate the purchase of this state-of-the-art “toy” by discussing the real organization value that they supply.

Giuffre Contracting in Albany, NY recently wrote a post about how they use drones to help them better inspect their customers roof systems.

Why buy a drone for your roofing company?

– Inspect difficult to access roofing sections and reduce time spent in the “risk zone”

– Create detailed aerial measurement reports

– Create professional quality footage of your jobs to utilize in your marketing products

– Make an enduring impression on your clients while closing more sales

Now that you’ve encouraged your accounting professional, business partner, employer and so on that you need a drone. Here’s what you need to know …

Step 1– Picking The Right Drone

There are a ton of choices out there and the fact is, we’re not experts on whatever drone. We’ve never constructed a drone from a package or setup our own video up-link and we have no intentions of doing so. We desired something that was ready to fly right from the box so we picked the most significant consumer drone business out there, DJI. DJI makes a few excellent drones that are a terrific location to begin.

The DJI Phantom 3 and 4: The existing DJI Phantom 4 and the earlier DJI Phantom 3 are cost effective and capable drones that will get you working in minutes. (We had a Phantom 2, which was terrific as well but the video camera had a broad angle lens and required lens correction prior to getting accurate roofing measurements from the image. The newer designs don’t have this concern, making the aerial imagery perfect to utilize.).

The DJI Inspire: The Inspire is an expert grade flying video camera that’s an action above the Phantom. If you have the spending plan, the Inspire will do everything you want and more.

Obviously, there are a lots of other choices out there however we’ll stay with the ones we know. Here are a few things to search for if you stray the beaten path:.

·      Capable of High Altitude: You’ll need a drone that’s capable of flying to about 400 feet, which is the optimum enabled by the FAA. This height is needed to reduce any perspective distortion on the image in order to get accurate measurements.

·      A Camera that can Look Straight Down: Some of the cheaper drones cannot in fact tilt the camera directly down to get a direct overhead shot of the roofing system. Straight shots are needed in order to get right measurements from the drone.

·      Battery Life: You should be able to get 20 minutes or more out of a battery. You do not desire the charge to run out in the middle of a roofing evaluation and spare batteries are typically costly. Ensure you get lots of flying time on a charge.

·      Capable of Handling Wind: You’ll want something that can fly when it’s a bit breezy. A sturdy drone with powerful motors must be able to fly on the majority of days.

·      HD Video Uplink: You’ll want to see HD video of precisely what the drone is seeing. This makes flying much easier and enables you to identify problem areas on the roof.

·      GPS Guidance: It is exceptionally hassle-free to fly a drone with GPS. When you release the controls, it ought to stay practically where you left it.

Step 2– Getting Some Practice.

So you simply bought a $3,500 Inspire drone and are thrilled to examine your very first roofing system with it. Here’s the best ways to lower your chance of bouncing it off of a roofing system on your first flight in front of a consumer and conserve yourself the expense and pity of a crash. (I will not point fingers, however somebody here in the office still has not had the ability to live down the embarrassing crash of our old Phantom 2.).

Exactly what’s the technique? Attempt a little quad rotor drone can be discovered on Amazon for about $20 and the fundamental controls are the same as the big ones. They’re remarkably rugged and can be bounced off of the walls in your house or workplace dozens of times prior to being damaged. They are likewise MUCH more difficult to fly. As soon as you’ve effectively piloted one of these around your living-room, you’ll be impressed at how easy the huge ones are.

Step 3– Legal Stuff.

The FAA recently released some brand-new laws impacting drone flight. Be sure to examine your city ordinance for regulations.


Installing Metal Roofing Options

Choosing the maximum roof can be a technical choice. When confronted with the possibility of setting up a new roofing system, it can be tough to understand if the decisions you’re making are the right ones. It may even be confusing to understand exactly what result each of these choices is going to have in the future!


Today, we’re going to help you comprehend metal roof installation better. When moving forward with metal roof, we will assist answer concerns such as:


– Which fastening technique is finest?

– Why does it matter?

– What are the benefits?


These may seem like relatively basic concerns, but it is the cause of some argument in the roofing contracting world.


Some alternatives are as follows:


1. Exposed Fastener System (believe screws that you can see when looking at your roofing);.


2. Hidden Fastener System aka Standing Seam Roof (think screws that exist but hidden by the panel);.


3. Concealed Adhesive Fastening System (think adhesive and no screws or holes).


What You Need To Know About Exposed Screw Fastener Metal Roofing Systems.


Exposed Fastener typically describes a visible screw fastener that is being utilized to permeate through the roof product. However, this traditional method of roofing attachment has actually proven to be troublesome since the exposed screws used throughout setup have the tendency to be over tightened up, rust, or back out in time.


How does a screw “back out?” When your metal roof is exposed to severe temperatures and weather, the metal will broaden and contract. In time, this thermal motion of the metal panels puts recurring pressure on the countless screws in your roofing causing the screw holes to increase the size of. When this occurs, screws can loosen and revoke the wood deck. When the screw ends up being loose or revokes the roofing altogether, you now have an opening on your metal roof which can trigger a leakage.


In general, Exposed Fastener roofing has actually shown itself to be a threat for leaks. The useful danger presented by this vulnerability is not completely avoidable and has actually been enough to hinder lots of house owners from moving on with this kind of through-fastened panel.

As a general guideline, exposed fastener roof is more cost effective than standing seam roof. You can install a stunning looking roofing system for less money by choosing an exposed fastener system, but you may be compromising in the arena of longevity.


What You Need To Know About Concealed Screw Fastener metal roofing Systems.


Hidden Fastener Systems, usually standing seam systems, provide metal panels with raised interlocking joints. Screws are utilized to attach the side fastener fins into the roofing system deck. While this type of system conceals the screws that are utilized for installation, standing seam roofings are prone to fastener tension which can trigger unpleasant oil can dimpling of the metal panels. Standing seam systems also make use of fastener slots or attachment clips developed to enable thermal motion of the panels, however incorrect fastener placement limitations this function.


Setting up a standing seam roofing is labor-intensive and can be costly. This can be a deterrent for many homeowners.


What You Need To Know About Concealed Adhesive Roofing Systems.


Hidden Adhesive roofing systems are a new development to the metal roofing market. While standing joint was when known as the “brand-new and enhanced” roofing choice in the 1980’s, more research has actually been performed to enhance systems that have weaknesses.

As a property owner, does it make sense to buy a roofing option that requires thousands of screws that trigger holes or dimpling in your metal roofing system? Basically you are paying for somebody to poke holes in the very thing that is protecting you from outdoors components.

The market bore in mind of this problem and began trying to find the next “brand-new and enhanced” strategy to offer a service for homeowners who desire the look of metal, without compromising the integrity of the very product they are purchasing.


The Bottom Line.


When seeking to re-roof or even construct a new home, picking a metal roof will offer you the durability, performance, and charm you are trying to find. Now that you know about all 3 metal roofing attachment approaches, you can make a smart and educated choice about the metal roof you are purchasing.


If you ‘d like more information on metal roofing and how it can be a terrific solution for your home or organization, visit www.expexts.com.

Roofing Shingle Service Warranties – What You Need to Know

The Basic Warranty

Wind also causes shingles to warp, which not only allows more moisture and particles, but can also cause shingles to break or snap.

Wind Service warranty

High winds can be extremely harmful to shingles. Effective gusts will rip the shingles from your roofing, but even weaker winds can trigger pricey damage.

Shingles will lift, even if just for a second, in strong adequate winds. This can be the start of 2 problems. First, when the shingle lifts, particles and moisture can blow in under the shingle. As soon as the shingle go back to its initial position, it traps the debris and wetness. If there is excessive moisture, it could leak through your roofing system and harm your home. The caught particles also keeps the tile from lying completely flat, which lets in more wetness and debris.

No matter which roof shingles you select, they should abide by government standards and have a minimum warranty that the shingle will perform as assured. Guarantees usually range from 15 to 40 years, but there are an increasing variety of shingles readily available with a lifetime service warranty.

It is essential to note that many shingle manufacturers have specific installation instructions and inappropriate installation of your roof shingles can void your service warranty.

While roofing shingle warranties are typically thought about requirement, there can be substantial differences in guarantee protections in between similar shingles. Perhaps most importantly, some warranties just cover the expense of the shingles, but not the labour had to get rid of the old roofing system and set up the new one.

Algae Resistant Service Warranty

Algae development is a common roofing problem that causes dark streaks on your roofing shingles. The algae can be cleaned away, however it will likely return, particularly if you live in a humid climate. If you have actually had algae problems in the past, you need to search for algae-resistant coverage on your shingle service warranty.

Visit www.aceroofco.com for more shingle service warranty information

The Advantages of Using Drone Technology in the Roofing Industry

Given that the FAA updated its policies controlling non-recreational use of tiny, unmanned airplane systems (UAS), or drones, in August 2016, it has actually become less complicated for roofing contractors to capitalize on this promising modern technology while still staying within the laws.

These brand-new laws lead to excellent information for the roof covering sector. Here are six ways drone modern technology can possibly benefit your roof organization:

Cost savings:

Take into consideration just how much money you might conserve in automobile as well as gas costs if you no more needed to roll a large pickup truck with ladders for every single assessment. Additionally, measuring the job might take less time, allowing your study employees to go to even more sites in a day.


Conserve money and time– as well as enhance safety– by utilizing a drone to take dimensions of the roof prior to developing your estimate. Drones also supply industrial contractors the capacity to do a survey of the website, which may prove beneficial when establishing points of entry as well as leave to the jobsite, in addition to determining the most effective positioning for product as well as car parking.


Take video and also imagery of the whole roofing system to reveal the proprietor the problem the roof covering is in. This can consist of a drone-based thermal imaging examination to look for leakages and dampness, which FLIR supplies to GAF factory-certified professionals. Drones might be especially beneficial for inspections of very steep roof coverings where there could be additional risk of getting up on the roofing. When the drone assessment takes place, you can utilize this details to examine with the property owner or structure owner any troubles and explain exactly how you can repair them.


Drones could assist you look extra professional in the eyes of the home owner or structure owner. Set your firm aside from a rival and also excite your potential consumer with a remarkable, interesting video.


Lowering the have to often climb onto high roofings might turn you into a much more appealing firm to benefit, and aid attract and retain a more diverse team of beneficial workers.


Before-and-after videos are effective marketing devices. Place them up on your internet site, show them to possible clients, and show the difference you can make through your top-quality product and also installment. There’s a reason drone technology has actually come to be common in property advertising and marketing: it adds sizzle for prospective customers!

Initially, it is critical for you to know the legislations and license requirements that accompany utilizing drones. Protect yourself and your company by making sure you have the information you need.

Visit this website for more information on drone usage in the roofing industry – www.expexts.com

Please note that the materials and information included in this post are for educational purposes just and not for the objective of providing lawful advice, not a replacement for obtaining lawful guidance from a qualified attorney and also ought to not be acted on as such. You must not act upon any of the information included at this blog post without first looking for qualified expert advice for your details requirements and also you ought to contact your attorney to acquire recommendations relative to any type of particular concern or problem. The details presented in this article might not be current as well as undergoes alter without notice.

Copper Is the Solution for Challenging Residential Roof Restoration

Copper Is the Solution for Challenging Residential Roof Restoration

This home in Alexandria, Va., was retrofitted with a copper double-lock standing seam roof system

This home in Alexandria, Va., was retrofitted with a copper double-lock standing seam roof system installed by Wagner Roofing. The 16-ounce copper roof panels were 17 inches wide. Photos: Landmarks Photography—Jay Stearns

“We like the tough jobs,” says Dean Jagusch, president and owner of Wagner Roofing Company. “We like the intricate jobs.”

Headquartered in Hyattsville, Md., Wagner Roofing has served the Washington area market for more than a century. “We specialize in historic restoration and innovative architectural roofing and sheet metal,” Jagusch notes. “We’re full service. We do slate, copper, tile, and have a low-slope commercial division as well. But our trophy stuff tends to be of the steep-slope variety.”

A recent residential restoration project in Alexandria, Va., certainly qualifies as “trophy stuff,” taking home a North American Copper in Architecture Award from the Copper Development Association (CDA) in the “Restoration: Roof and Wall” category.

It’s easy to see why. The origami-inspired design features multiple roof angles, but the daring design was problematic. Even though the home was relatively new, the owners were plagued by leaks. Along with Restoration Engineering Inc. of Fairfax, Va., Wagner Roofing was called in to consult on the project, determine the source of the leaks, and come up with a solution.

The original galvalume standing seam roof channeled the water into a large, stainless steel internal gutter with roof drains. Jagusch found that the leaks were occurring at two types of critical points. First, there were leaks where the internal roof drains met the central gutter. The other problem spots were along the pitch transitions.

Jagusch felt that installing a conventional-style painted galvalume roofing system in those spots was almost impossible. “We felt that was since it was an area that was failing, we wanted a metal we could work with when we met a transition and turn the panels vertical where we needed to without having to break them and rely on rivets and caulk,” he says.

Custom five-sided downspouts were fabricated

Custom five-sided downspouts were fabricated, but large windows at the back of the home offered few options for support. The downspouts were attached up under the framing system. Photos: Landmarks Photography—Jay Stearns

Copper was the answer. “The detailing was pretty tough to do, so we recommended changing it to copper so we could work with it, be able to solder and have a more seamless roofing assembly,” Jagusch recalls.

Another key to the project was redesigning how the roof drained. “We decided to push all the water to the exterior,” he says. “We collaborated with Restoration Engineering and we fleshed out the original redesign.”

The team decided that installing a copper roof system with a new drainage plan would be the best way to eliminate the leaks and keep the inspiring look the homeowners desired.

“We wanted to eliminate the drains and push all the water to the exterior, so that’s why we went for the re-slope of the big central gutter,” Jagusch says. “Also, at the transitions, we wanted to make sure we were 100 percent watertight, so we used a combination of turning up panels and soldered cleats to get everything into place.”

Solving the Puzzle

With its intersecting planes, the roof made laying out the panels an intricate puzzle. “You also had large expanses of roofing that changed pitch throughout,” Jagusch explains. “Panels had to be laid correctly because not only does the roof slope up, but it also slopes sideways. The layout of the panels was critical from the get-go. We all looked at it and agreed that we would follow parallel to the actual trusses, which we felt was the best solution.”

The old roof system was removed and stripped down to the 3/4–inch plywood deck. “We covered the entire roof deck with Grace Ultra,” said Jagusch. “We then used a slip sheet and installed 1-inch-high, double lock, 17-inch-wide, 16-ounce copper standing seam panels.”

Photos: Landmarks Photography—Jay Stearns

Photos: Landmarks Photography—Jay Stearns

Panels were roll formed at the Wagner metal shop out of 20-inch-wide coils using an ESE roll former and trailered to the jobsite. Approximately 5,400 square feet of copper panels were installed on the project. The double-lock seams were mechanically seamed. Twenty-ounce copper flat-seamed panels were used in the large valleys.

The safety plan included full scaffolding during every phase of the project. “We have our own safety scaffolding system,” Jagusch says. “Our guys demand it on our jobs, and we demand it of them to come home safely every day. We are very proud of our safety record. It’s front of mind for us.”

In addition to the roof, all of the metal cladding was replaced on the southeast feature wall. The top of the wall was reconfigured to accommodate the new sloped valley. Where the wall met the roof, a band was fabricated to match the top part of the fascia. Other details included copper cladding for the chimney.

Drainage was redirected to the perimeter, where custom-fabricated gutters were installed. “On the west side, the roof was originally designed to dump off straight onto a rock feature on the ground, but we fashioned a custom copper box gutter about 35 or 40 feet long,” Jagusch states.

At the either end of the large internal gutter and at the end of a large valley, shop-fabricated copper conductor heads were installed. Custom five-sided downspouts were fabricated, but installing them posed another challenge, as large window areas offered few options for support. The downspouts had to be snugged up under the framing system.

“Everything had to work with the other building components,” Jagusch explains. “One of the tougher things on this project was being able to have the function and the form both top of mind, in that order. The key was to make the functional stuff look good.”

Showpiece Project

The project was completed about a year ago, and the copper has begun to change in color. “The copper now has a gorgeous bronze, kind of purplish hue to it,” notes Jagusch. “I think it will eventually develop a green patina, but with the way the environment is these days, I think it will take 15 years or so before it gets to that point. That’s the cool thing about copper—it’s a natural, breathing material that is constantly changing, constantly evolving.”

Copper cladding was installed on a feature wall

Copper cladding was installed on a feature wall, which also featured changes in slope. The top of the wall was reconfigured and a band was added to match the top part of the fascia. Photos: Landmarks Photography—Jay Stearns

Wagner Roofing has a maintenance agreement in place on the home, so Jagusch has stayed in touch with the owners and kept tabs on the project, which is performing well. “I’ve got just one hell of a team here,” he says. “It wasn’t just one estimator that went out and brought this thing in. In our business, estimating and roofing is a team sport. We kicked this thing around a lot with all divisions of the company, from estimating to operations to the actual installers before we finally settled on a number for this thing.”

“We work on some pretty spectacular places, and of course this is one of them,” he concludes. “We like a challenge, and this is the stuff that my team really loves to get their teeth into.”

Published at Wed, 04 Oct 2017 07:00:46 +0000

K-NRG Seal™ VP

K-NRG Seal™ VP

KARNAK, an industry-leading manufacturer of reflective coatings, sealants and cements, recently announced the launch of K-NRG Seal VP, a high-performance vapor-permeable air barrier for above-grade wall application.   

K-NRG Seal VP expands KARNAK offerings, which include roofing, damp-proofing and waterproofing products; fabrics and repair tapes; caulks, sealant and flooring products; and elastomeric products.  

Published at Wed, 04 Oct 2017 13:00:00 +0000

MRCA to Release SHARP New Employee Orientation Video at 2017 Trade Show

MRCA to Release SHARP New Employee Orientation Video at 2017 Trade Show

There will be a show-only special price for this new SHARP video for anyone attending the free trade show October 17 and 18.

MRCA is releasing a new edition of the SHARP new employee orientation video. The video is a helpful tool for training new members of your crew.

See a preview of the video.

Contractors receive a free trade show pass. Register online today.

Published at Wed, 04 Oct 2017 14:51:13 +0000